Crystal Bro 250ml – Ultimate Shine & Protection for Your Car

Instructions for use – Crystal Bro

For external use only – NEVER use internally

⚠️ IMPORTANT – READ FIRST

Avoid contact with water during curing.

Do not expose the surface to rain, moisture, or snow for at least 48 hours after application.

Crystal Bro is self-leveling.

Do not dab, buff, or wipe the product after application.

Leave the product to dry — it will level itself while curing.

After the product has leveled (approx. 2–3 hours):

The paint may be touched very gently if needed.

Light marks may appear — these can be removed by:

using a lightly damp cloth

wiping them away with gentle strokes

always drying immediately afterwards so water does not dry on the coating

This applies only after the surface has leveled — not immediately after application.

Important application rules

Use plenty of product.

The microfiber cloth must be properly saturated — never apply with a dry or nearly dry cloth.

DO NOT go over the same area again after about 5 seconds.

The product will start to set and can cause marks, hazing, or uneven results.

Apply in one direction: left → right, top → bottom, section by section.

Avoid high humidity — garage/indoor application is recommended.

Always test first on a small hidden area.

1. Important before you start (Preparation – step by step)

1.1
Use only on automotive paint.
❌ Do not use on wraps/PPF, paint protection film, “invisible car cover”, glass, or carbon fiber.

1.2
Not recommended for cars newer than 6 months.

1.3
Always test on a small, hidden area (e.g., trunk lid or fender).

1.4
Do not apply in rain or very high humidity.

1.5
Work in a well-ventilated area (preferably indoors/garage).
The product is flammable – keep away from heat, sparks, and open flame.
No smoking.

1.6
Protection: use protective gloves and eye protection.

1.7
After the product has leveled (approx. 2–3 hours):

The paint may be touched very gently if needed.

Any light marks can be removed by:

using a lightly damp cloth

wiping with gentle strokes

always drying immediately afterwards

2. Step-by-step application

2.1
Wash the car thoroughly with a pH-neutral car shampoo.

2.2
Degrease the paint completely with degreaser or IPA to remove wax, grease, and old protection.

2.3
Apply Crystal Bro with the supplied microfiber cloth.

2.4
Ensure the cloth is properly saturated with product.

2.5
Apply evenly over the paint, section by section, from left to right and top to bottom.

2.6
Avoid going over the same area again if about 5 seconds have passed.

3. Extra tips (to reduce marks)

3.1
Add more product to the cloth as needed so you don’t drag it dry, and keep the same application direction at all times.

4. Curing & aftercare

4.1
Allow the product to dry and cure.
Best results are achieved indoors for at least 3 hours.

4.2
For best results:
Keep the car indoors overnight if possible.
Morning dew/outdoor moisture can affect curing if the car is left outside.

4.3
In rain or high humidity, the paint must not be exposed to water for at least 48 hours.

5. If water gets on during curing

5.1
Gently dry immediately by blotting or very light wiping — do not rub hard.

5.2
Avoid car care products and strong chemicals for:

4 days in summer

7 days in winter

5.3
Before the first proper car wash:
Check that the product has cured fully, preferably on a hidden area.

6. If something goes wrong

6.1
Inspect the entire car immediately after application.
If you see marks, pinholes, or irregularities — remove immediately with degreaser and reapply.

6.2
If the product has cured for too long, polishing may be required to remove it.

7. Emergency safety

7.1 Skin contact
Wash with plenty of water and remove contaminated clothing.

7.2 Eye contact
Rinse gently with water for several minutes.
Remove contact lenses if possible and continue rinsing.
If symptoms persist — seek medical attention.